| SERVICE | PRODUCT | DETERMINANT | TECHNIQUE | PROCEDURE | LIMITATION / RANGE | Evaluation of electrical appliances and devices - Performance
| Water heaters;
| Boiling time and efficiency; Electrical energy consumption; Overflow; Pressure measurement; Strength and dimensions of components; Temperature control; Temperature distribution; Torque;
| Not applicable;
| AS 3498 Section 7.2, Appendices A, B, C; AS/NZS 4692.1 Sections 2.2.2, 2.2.3, 2.2.4, 5.2.1, 5.2.3, 5.3, 5.5.2.1, 5.6.5; AS/NZS 6400 Sections 2.1, 2.1.4, 2.2, 2.2.4, 2.3, 2.3.4, 2.4, 2.4.4, 2.5, 2.6,2.6.4, 2.7, 2.7.4
| | | Material performance evaluation of elastomers, plastics and composite products
| Hosing material; Pipe material and related products;
| Adhesion; Bending properties; Compression; Dimensional stability; Dimensions; Flexing; Formability; Heat resistance; Impact resistance; Pull-out strength; Strength;
| Not applicable;
| AS 2053.1 clauses 8.1, 8.2, 8.3, 8.4, 9.2, 9.3, 9.4, 9.5, 9.6, Appendices A, B, C, D; AS 2053.5 clauses 6, 7, 8, 9, 10, Appendices AA, BB, CC, DD
| | | Mechanical performance evaluation of components for building envelopes, framing and interior lining
| Cable trunking systems;
| Cable trunking system cover retention; Cable trunking system supporting capacity; Deflection; Dimensions; Finish; Impact resistance; Resistance to linear deflection; Squareness; Strength at ultimate limit state loading; Structural performance evaluation;
| Not applicable;
| AS/NZS 4296 clauses 8, 9, 10, Appendices D, E, F, G
| | | Performance evaluation of healthcare equipment and related items
| Medical suction tubing;
| Dimensions; Flow rate; Mass; Vacuum pressure - Degree of collapse;
| Not applicable;
| AS 2120.3 clause 5.2, Appendix A
| | | Products and appliances connected to the water supply - Physical evaluation
| Sanitary fixtures - Urinals, water closet pan/suites, bidets, douche seats, cisterns and purpose built bathroom modules;
| Discharge; Flush performance; Flush volume; Hydraulic strength; Leakage; Leak tightness; Load; Splash; Wetting;
| Not applicable;
| AS 1172.1 clauses 3.1, 3.2, 3.3, 3.4, 3.5, 3.6, 3.7, 3.8, Appendices A, B, C, D, E, F, G, H; AS 1172 clauses 4.2, 4.3, 4.7, Appendices A, F; AS 1976 clauses 5.2, 5.3, 5.4, Appendices A, B, C; AS/NZS 3662 clauses 5.1, 5.2, 5.3, 5.4, 5.5, Appendices B, C, D, E; AS/NZS 3982 Appendices A, B, C, D; WMTS 5200.004 clauses 9.3, Appendix C; WMTS 5200.020 clauses 9.2, 9.3, 9.4; WMTS 5200.021 clauses 9.2, 9.3; WMTS 5200.051 clause 9.2, Appendix B
| | |
| Food waste disposal units;
| Air gap; Back flow; Degree of fineness (FWDU); Drainage;
| Not applicable;
| WMTS 5200.028 clauses 9.1, 9.2, 9.3, 9.4
| | |
| Baths, sinks and basins;
| Endurance; Flow rate; Flush performance; Leak tightness; Spread angle; Strength of assembly; Thermal distortion;
| Not applicable;
| AS/NZS 3662 clauses 5.4.1, 5.4.2, 5.4.3, 5.4.4, 5.5, 5.6.1, 5.6.2, Appendices B, C, D, E, F (2005); AS/NZS 3662 clauses 5.5.1, 5.5.2, 5.5.3, 5.5.4, 5.6, 5.7.1, 5.7.2, Appendices B, C, D, E, F; AS 3982 clauses 1.6.1, 1.6.2, 1.6.3, 1.6.4, Appendices A, B, C, D; AS 4775 clauses 6.5.1, 7.3.1, 8.3; AS/NZS 6400 clause 2.1.3
| | |
| Water service products - Connectors, filters, fittings, hoses and pipes;
| Air gap; Air separation distance; Bending properties; Compatibility; Crack propagation; Dimensions; Endurance; Flow rate; Functionality; Impact resistance; Joint strength; Leakage; Leak tightness; Load; Ovality; Pressure; Pressure cycling resistance; Rigidity; Seal integrity; Sliding fit; Socket fit; Strength of assembly; Thermal cycling; Thread form evaluation; Torque;
| Not applicable;
| AS/NZS 1260 clauses 3.2.1, 3.2.2; AS 1432 clauses 4.3, 5.4.2; AS/NZS 1462.1 clauses 7, 8, 11; AS/NZS 1462.4, AS/NZS 1462.6; AS/NZS 1462.8; AS/NZS 1462.10; AS/NZS 1462.11; AS/NZS 1462.13; AS/NZS 1462.17; AS/NZS 1462.24; AS/NZS 1462.29; AS/NZS 1477 clauses 3.3.1, 3.3.3, 3.3.6, 3.4.1(b), 3.4.2, 3.4.3, 3.4.4, 3.5.1, 3.5.2; AS 1571 clause 8.2; AS 1589 clauses 1.7.4, 1.7.5, 1.9.2, 1.10, 1.13.3 up to DN 80, 3.3.1, 3.3.2, 3.3.3, 3.3.4, 3.3.5, 3.4.1, 3.4.2, 3.4.3, 3.5.1, 3.6.1, 4.9.1, 4.9.2, Appendices E, G, H; AS 1926.3 clauses 5, 6.1, 6.2, Appendices A5.1, A5.2, A5.3, A5.4, B; AS 2280 clauses 2.5.2, 3.1, 3.1.1, 3.1.2.1, 3.1.2.2, 3.1.2.3, 3.1.2.4, 3.5.2.1, 3.5.2.2,4.2.2, Appendices F, H; AS 2419.3 clauses 4.2, 4.2.3, 4.2.3, 4.3, 4.3.2, 4.3.3, 4.3.4, 4.3.5, 4.3.6; AS/NZS 2492 clauses 3.8, 3.9; AS 2537 (1994) clauses 11.2.1, 11.2.3, 11.2.4, 11.2.5, 11.2.6, 11.2.7, 11.2.8, 11.2.9; AS/NZS 2537.3; AS/NZS 2642.3 clauses 12.2.1, 12.2.2, 12.2.3, 12.2.4, 12.2.5, 12.2.6, 12.2.7, 12.2., AS 2887 clauses 2.6.1, 2.6.3, 2.6.5; AS 2888.1; AS 2888.2; AS 2888.3; AS 2888.4; AS 2888.5; AS 2888.6; AS 2888.7; AS 2888.8; AS 2888.10; AS 3499 Clauses 8.2, 8.4, 8.5, 8.8, 8.9, Appendix C; AS 3518 (2004); AS 3688 clauses 3.2, 3.4, 3.5, 3.6, 3.7.1, 3.7.2, 3.8, 4.2, 4.3, 4.4, 4.5, 4.6, 4.7, 4.8, Appendices C, D, E, F, G, H, I, J, K, L; AS/NZS 4129 clauses 1.8, 1.13.1, 1.13.2, 2.4.2, 2.4.3, 2.4.4, 2.4.5, 3.4, 3.5, 4.4.2, 4.4.3, 4.4.4, 4.4.5, 4.4.6, Appendices D,E; AS/NZS 4130 clauses 9.1, 10.1, 10.2, 10.4; AS/NZS 4327 clauses 4.1, 4.2,Appendices B, C, D, E, F; AS/NZS 4401 clauses 6.2, 6.3, 6.4, 7.2, 8; AS/NZS 4441 clauses 10, 11.1.1, 11.1.2, 13.2, 13.3, 13.4; AS/NZS 4765 clauses 3.2.3, 3.2.4, 3.2.7, 3.2.8, 3.2.9, 3.2.10, 3.3.1, 3.3.2, 3.3.3, Appendices B, D, E; AS/NZS 4793 clauses 4.1.2, 4.1.3, 4.1.5, 4.1.6, 4.4.1; AS/NZS 4798 Clause 3.3, 3.4, 3.5.1, 3.5.2, 4.2, 5.2, 5.3, 5.5, 5.5.5; AS/NZS 5065 clauses 3.3.1, 3.3.2, 3.4.1, 3.4.2, 3.4.3, 5.2; AS 5082.2 clauses 12.1, 12.2, Appendices C, D, E, F, G, H; AS/NZS 6400 clause 2.7.3; WMTS 5200.040 clause 9; WMTS 5200.053; WMTS 5200.475 clauses 9.2, 9.3, Appendices B, C; WMTS 5200.477 clause 9.4, Appendix C; WMTS 5200.482; EN 713; EN 714; EN 1053; EN 1054; EN 1055; EN 12293; EN 12294; EN 12295; ISO 1167.1; ISO 1167.2; ISO 1167.3; ISO 1167.4;; ISO 3126; ISO 3459; ISO 3501; ISO 3503; ISO 13257; ISO 13479; ISO 13844; ISO 13845; ISO 13846; ISO 13954; ISO 13955; ISO 16422 clauses 10, 11.1.1, 11.1.2, 13.2, 13.3, 13.4; UK-WIS-4-24-01
| | |
| Tap assemblies; Valves;
| Back flow; Bending properties; Closing pressure; Compatibility; Dimensions; Distortion; Endurance; Flow rate; Functionality; Hydrostatic pressure; Leakage; Leak tightness; Load; Pressure; Seal integrity; Spread angle; Strength of assembly; Thermal cycling; Torque;
| Not applicable;
| AS 1357.2 clauses 3.2, 3.3, 7.2, 7.3, 7.4, 7.5, 9.4, Appendices E, L, M, N, V, W; AS 1628 clauses 4.2, 4.3, 4.4, 4.5, 5.6, Appendices B, C, D; AS 1910 clauses 4.2, 4.3, 4.4, Appendices C, D, E; AS 2419.2 clauses 4.3.2, 4.3.3, 4.3.4, 4.3.5, 4.3.6, Appendices D3, D4, D5, D6, D7; AS/NZS 2638.1 clauses 5.1.2, 5.1.3, 5.1.4, 5.1.5, 5.1.6, 5.1.7, 5.1.8, 5.1.9, 5.1.10, 5.1.11, 5.1.12; AS/NZS 2638.2 clauses 3.2, 3.3, 5.1.1, 5.1.2, 5.1.3, 5.1.4, 5.1.5, 5.1.6, 5.1.7, 5.1.8, 5.1.9, 5.1.10, 5.1.11, 5.1.12, 5.1.13, 5.1.14, 5.1.15; AS/NZS 2845.1; AS 3498 Appendices A, B; AS/NZS 3718 clauses 43.11, .3, 4.5, 4.6.2, 4.8, 4.9, 4.10, 4.11, 4.12, 4.15, Appendices D, F, G, H, I, J, K, L, M, Q; AS 3952 clauses 3.3.1, 3.3.3, 5.1.1, 5.1.2, 5.1.3, 5.4.1, Appendix A; AS 4032.1 clauses 4.3, 4.4, 4.5, 4.6, 4.7, 4.8, 4.9, 4.10, Appendices D, E, F, G, H, I, J; AS 4032.2 clauses 3.2, 3.3.1, 3.3.2, 3.4, 4.4, Appendices C, D, F, G; AS 4794 clauses 5.1.2, 5.1.3, 5.1.4, 5.2.2, 5.2.3, 5.2.4, Appendices D, E; AS 4795 (2006) clauses 5.2.1 Test A, 5.2.2 Test B, 5.2.3 Test C, 5.2.4 Test D, 5.2.5 Test E, 5.2.6 Test F; AS 4796 clauses 4.2, 4.3, 4.4.1, 4.5, 4.7, 4.8, Appendices E, F, G, H, I; AS 5081 clauses 5.2.2, 5.2.3, 5.2.4, 5.2.5, 5.2.6, 5.3,2, 5.3.3, 5.3.4, 5.3.5, 5.3.6, 5.3.7, 5.3.8, 5.3.9; AS/NZS 6400 clause 2.6.3; WMTS 5200.006 clauses 8.1, 8.3, 9.1, 9.2, 9.3, 9.4, Appendix A; WMTS 5200.012 clauses 9.2, 9.4.1, Appendices B, C; WMTS 5200.030 clauses 9.3, 9.4, Appendix C; WMTS 5200.037.2 clauses 8.1, 9.2, 9.3, 9.4, Appendices B, C, D, F; WMTS 5200.053 clause 9; WMTS 5200.460 clause 9.1; WMTS 5200.467 clauses 8.1, 8.3, 9.1, 9.3.2, 9.4; WMTS 5200.476 clauses 9.1,9.2; WMTS 5200.477 clauses 9.2, 9.3, 9.4, 9.5, Appendices B, C, D; WMTS 5200.481 clauses 9.2, 9.3, 9.4.1, 9.4.2, 9.4.3, 9.5, Appendices B, C; ISO/EN 817 clauses 8.3, 8.4, 8.5, 8.6, 8.7, 9.4, 9.5, 10.2, 10.4, 10.5, 10.6, 10.7, 11.2, 12.1, 12.2, 12.3, 13, Annexes A, B; ISO 5208 clauses 4.8, 4.9, 4.10, 4.11, 4.12
| | |
| Water treatment appliances and systems;
| Burst pressure; Endurance; Hydrostatic pressure; Strength of assembly;
| Not applicable;
| AS/NZS 3497 clauses 5.2, 5.3, 5.4; WMTS 5200.103 clauses 9.2, 9.3, 9.4; WMTS 5200.104 clause 9.3; WMTS 5200.105 clause 9.3
| | |
|
Printable version